[ - Antworten - Zitieren - Direktlink - ]

[ - Antworten - Zitieren - Direktlink - ]

[ - Antworten - Zitieren - Direktlink - ]

[ - Antworten - Zitieren - Direktlink - ]

[ - Antworten - Zitieren - Direktlink - ]

@MaikG:
Wenn Du die CPU nicht mehr syncron zu den Gals taktest, bringt Dir das auch nicht viel. Meine Karte hat 33MHz gemacht nach einem Umbau.
Es war nicht wirklich viel was das gebracht hat. Es gibt aber so ein
Quaddoubler glaube ich hiess das Ding, da kann man 50MHz 68040iger betreiben.

Gruss Musicman

[ - Antworten - Zitieren - Direktlink - ]

[ - Antworten - Zitieren - Direktlink - ]

Dave's Amiga Hardware Page
--------------------------

Overclocking the Commodore A3640 :
http://members.iinet.net.au/~davem2/overclock/a3640.html

The A3640 is the standard 68040 CPU card supplied for A3000 and A4000 Amigas. It is easy to overclock, there being a single 14-pin DIL form-factor crystal rated at 50MHz in the centre of the board. The A3640 also provides some of the motherboard timing, which may cause problems at certain overclocked frequencies. Note that the A3640 halves the oscillator frequency in use so that at 25MHz it actually uses a 50MHz oscillator.


I have overclocked three of these boards, by replacing the 50MHz oscillator by one rated at 60MHz. This gives 30MHz for the 68040. All systems work reliably at this speed, and it's an ideal way to get some extra performance out of this board. I have heard of other people getting more. One user has been able to clock this board as high as 40MHz, and another I have heard of, has managed to get 37MHz. These two users were not able to get a lower speed of 33MHz, possibly because of the design of the A3640, which uses delay lines for part of it's clock circuitry. These delay lines provide a fixed amount of delay which becomes inappropriate when the clock frequency is changed too much. I suspect a "wrap around" effect occurs when the frequency is increased still further, the amount of delay once again becoming more or less correct over 37MHz or so. Recently I have become aware that it is possible to change the amount of delay from this delay line, so that it is now possible to overclock to frequencies such as 33MHz, and possibly more.


I recently had an opportunity to try this delay line modification at a recent Overclocker's workshop, held by the Melbourne Amiga Users Group. Unfortunately, I did not have a lot of time to really test it out. After performing the modification, and fitting an IC socket for the oscillator module, I first tried it at 40MHz. There were no signs of life. At 33MHz the Amiga booted perfectly and ran for about 10 minutes before locking up. It would not reboot at all after that. I then tried 31MHz, and it worked perfectly for the remainer of the night. I suspect overheating was the problem, although nothing on the A3640 got unusually hot. If I had the time, I would have liked to try it with a fan on the 040, and the A4000's case modified for better airflow. Although these results seem ambiguous, I had noted that the A3640 wouldn't even boot at 33MHz with the unmodified delay line on other A3640's I had overclocked previously. I also noticed that the A3640 would still work at the standard 25MHz after this modification, although I didn't have the time to test for proper reliability. Since then I have heard of someone who has successfully overclocked his A3640 to 33MHz, using the cut and jumper mentioned above. He also found his board would not work at 33MHz if the cut and jumper was not done. It seems that the particular 040 in my friend's Amiga could not cope with 33MHz - a classic example of "your mileage may vary".
--
Proud member of www.AmigaClub.be

[ - Antworten - Zitieren - Direktlink - ]

[ - Antworten - Zitieren - Direktlink - ]

[ - Antworten - Zitieren - Direktlink - ]

[ - Antworten - Zitieren - Direktlink - ]